Knowledge of the electric guitar line

Knowledge of the electric guitar line in the electric guitar, effects, and speakers to spend on things that Big Three million is a matter of course in the hands of guitar


, but spend a hundred dollars to buy a guitar line is not easy to accept. High-end guitar lines are not necessary to choose


it?


many effects and the speaker, the background noise is very low, but we also often hear the noise of their


complaints sound problems, some of the noise criteria for judging the size of the problem, most of it is because too much use of quality


caused by poor guitar lines.


guitar line is the structural integrity of the antenna itself, so often will be from the stage lights, transformers and their


his electronic equipment electromagnetic radiation interference, the noise signal. This electromagnetic radiation noise shield with a mesh that is


addresses, use the mesh shield is also the minimum requirements for the quality of the guitar lines. Check the screen quality is very simple to


guitar front line can be straightened into the display, a good guitar line there should be no noise intensity. (You use the


LCD monitor? ... ...)


theory, the shielding layer and the density of the material has little effect on the shielding effect, but in practice the guitar lines


is often stepped collapse or kink, in a stampede or bend where there will be local variations, noise,


so required a certain density and strength is necessary. Guitar line the outer plastic, nylon or rubber protective layer and the internal


shielding network, signal lines should not be any gap between the hand bend,Electric guitar parts, the shielding layer should not significantly close knit


degree of change.


guitar line there is a certain external strength requirements, the line quality is too soft will be very easy to produce hard-wrapped together or bend


off, use a lot of trouble, but also affect the sound. Outer protective layer of soft rubber material with a black guitar line is very easy to change


dirty, intensity of bad, the general high-end guitar cable will not use this material. Outer layer of nylon guitar line is the best


and will not age harden, and generally have a variety of colors to choose from, easy to distinguish.


low noise guitar line is very easy to find, but just do a low-noise guitar lines also failed


, and also must require sound.


sound of the guitar lines on the main guitar lines embodied in the difference on the capacitor. Capacitance and the length of the guitar lines


increases, high-frequency attenuation to increase. If the capacitance is too high or the guitar line is too long, high-frequency conduction velocity would be a clear


slower than low frequency, resulting in the phase drift, sound clarity and cohesion be much less.


capacitance effect on the sound use of high output impedance passive pickups (that is, without a battery electric guitar


him ...) and high input impedance of the speaker when the most serious, such as the traditional Fender speakers ride piano access tube


with (Speaker of the high input impedance tube and the tube itself will decay characteristics of Fender's treble to sound


more smooth and not harsh, it is sometimes a good sound from electrical defects ... ...). If your results


output impedance is low, then the effects mixer with speakers or the connection between the capacitor problem is on the sound effects


very slight.


specific to the stage to use, if you are at the foot of a speaker with a speaker simulator or synthesis of analog functions


effects, output standard signals to the mixer, then your guitar and effects must be a high quality connection between the


's, effects and mixers of good quality mid-range between the use of shielded cable. If you are at the foot of a few single-block effect


, effects connected behind a row of Marshall speakers, then the guitar and effects to the effects connected to the speaker


line to be used for high-quality line. If your feet are a few common single block effects (not DigitechX series that features with speaker simulation), connect a single block effect mixer, then .... Well ... ...

simply can not answer the!


If your effects device (such as SansAmpGT2) of the bypass function is true bypass (bypass switch is depressed after the input / output interface between the


directly connected), and you want to use to bypass / non-bypass the sound of two states, then it should use the high quality


cable.


the volume if you play great, sound feedback may also be generated by the guitar lines. Inner signal line and the guitar lines


shielding layer of insulation between the good performance can avoid this problem. (Did line their own friends, plug internal


signal line and the insulation shield should do very strict).


attached: electric guitar associated with the common equipment input / output matching


even the best guitar line, if used the wrong device will not have good results, it is clear


correct signal matching method is very necessary.


equipment connected electric guitar input signal specifications about 10dB/250mV/1M Europe (hereinafter referred to as the letter G


number), any effects or speaker of guitar input interfaces are designed with this specification. Therefore, no matter how


tandem, the guitar input of all equipment should be equal to G signal strength of the signal. Cascading effects in a single block


device, each single-output gain block (the volume) should be as close to G signal strength, to avoid an effect under


fruit device overload.


single block effects should not be directly connected to mixing consoles,Electric Guitar Electric, audio cards, general audio signals (hereinafter referred to as the letter S


number) input device. If you need this connection, connecting to a box should match the signal to the S signal strength.


general synthetic effects have dedicated output port for connecting need G signal or S signal input device


. For example, AX1500g 1 / 4 \

etc.; Zoom 707 can set the output interface for connecting the device type. Please refer to effects of specific operations manuals


. (Effects of the manual have the time or look at it, even the single-block effects are also very useful for the description


's. )


also some special cases. For example Digitech X-Series single block of effects built-in speaker simulation capabilities, and


and a S signal output interface for connecting the mixer or recording card. General type of special equipment are marked on the packaging


instructions.


rack effects are mostly the same time, G signal and S signal input, a qualified sound engineer will give you the choice


the correct interface.


some guitar speaker with high impedance / low impedance two input interfaces for connecting the general high-impedance guitar, low


effects such as impedance connection. Synthesis of high-end speakers and some effects are \

fruit device. Tuning stage of the \But not absolute, attention to reference the instructions


corresponding description.


if the effects from the mixer too far, the best balance with the effects 1 / 4 \

(if any), can effectively avoid the signal attenuation and noise. Too long XLR cable is not readily available, can be


effects in the time required to buy custom. If there is no balanced output type of interface should be closer in distance guitarist


place a device such as a synthetic effect of enhancing the signal after the long-distance transmission. For example, synthetic effects, guitar


15 meters from the mixer should be connected with three rice noodle guitar and synthesis effects, effects of 12 meters to connect with the mixer.


same distance of 15 meters, if the single block effects, guitar and effects, effects and guitar speaker should be between


the rice noodle with 3, if the volume is not enough guitar speaker, guitar speaker should use the microphone to pickup the mixer after the access is not


guitar speakers can be placed too far away from a single block of local effects.